How To Program A Genie Garage Door Opener: A Step-By-Step Guide

By Jack | Tips And Tricks

Jul 15
Three garage doors

Image via Pexels

Whether it's raining, snowing, or otherwise yucky outside, having a garage door opener is a blessing when you don't want to have to get out of your vehicle to open the door manually. However, an opener is only nice when you actually have the remote programmed properly, so it works. Imagine pushing the button, and nothing happens because you didn't learn how to program a Genie garage door opener. That would be a bummer.

Luckily, programming your remote is not too difficult. Genie provides complete instructions that are easy to follow. You just need to make sure you follow the right instructions, since there are several different types of garage door openers. Once you learn how to program a Genie garage door opener, you should have no trouble doing it again if you need to add a remote or replace one.

How To Program A Genie Garage Door Opener

In order to learn how to program a Genie garage door opener, you need first to figure out which type of remote you have. Genie has three basic remote types for its different garage door openers. You may need to consult your owner's manual to see which one you have. You may also be able to tell by the opener's operation buttons on the motor head. Once you know your remote type, it is just a matter of following the step-by-step instructions below.

Intellicode Remote

The first step in how to program a Genie garage door opener is to press and release the receiver learn code button on the motor head of the opener. This button is unmarked, but it is behind the light lens. When you press it, a light will start to blink. You then want to press your remote button three times. Make sure you are no further than two feet from the motor head when doing this. Press the button a fourth time and the door should operate, showing you have programmed the remote.

If you need to erase a remote or erase all remotes, which you should do if a remote is lost or stolen, then you want to hold down the receiver learn code button until the light stops blinking. This clears the programming. You will then need to reprogram the remotes you still have.

Intellicode II remotes

Again, the first step in how to program a Genie garage door opener using the Intellicode II remote is to go to the opener motor head. You will need to use the buttons located on the underside. Press and hold the square button until the blue LED comes on. Once the light is on, release the button. The long LED will start flashing purple, and the blue LED will go out. The blue light will go out before the purple light starts flashing, so do not press anything thinking this is an error. While no more than 5 feet away, press the remote button up to 5 times until the door begins operating, which indicates that you have programmed the remote.

If you need to clear the remotes, press and hold the square button until the blue LED comes on and wait for the purple long LED to start flashing. Then, you will press the two triangle buttons on the motor head until the purple LED turns off. This clears the programming for all remotes, so you will then need to reprogram the remotes you have.

Intellicode III remotes

How to program a Genie garage door opener for the Intellicode III is very similar to how you do it for the Intellicode II. You will press and hold the square button on the motor head until the LED turns blue. You then release it and press it again until the long purple LED comes on and blinks. Release the button, and using a remote that is already programmed, press it once to make the purple light solid. You can then program the new remote by pressing the button until the door begins to operate. Make sure to stand no further than 5 feet away when pressing your remote button.

If you do not have a programmed remote for this opener, you should consult your owner's manual. You may need to contact Genie for further assistance.

To clear your remotes, press and hold the square button to get to the long purple flashing light again. You will then need to hold the triangle buttons at the same time to get both LEDs flashing blue. Wait until they turn off. This indicates the remotes are cleared from the system, and you can reprogram your remotes as needed.

Wireless Keypad Programming

As part of your garage door opener, you also have a wireless keypad. Sometimes, you may need to reprogram that as well when you are dealing with how to program a Genie garage door opener. This is especially true if you're setting up your system. So, knowing how to program your keypad will come in handy. The following are general instructions. You should always consult your owner's manual to check the exact instructions for your unit.

Always make sure the backlight is off before you proceed. Put the unit into programming mode by pressing and holding the program button until the LED turns blue. Then, release and wait until the LED starts flashing purple. Enter the default PIN: 357. Press the up/down button slowly until the garage door starts to open.

You should change the PIN as well when first programming your keypad. To do this, enter the default PIN. Press the program button, and enter your new PIN, which can be three to eight digits. Finish by pressing the program button again.

House with two garage

Image via Pexels

Troubleshooting Your Garage Door Problems

If you are learning how to program a Genie garage door opener because you want to add a new remote due to an old one not working, you may find it helpful to do a quick bit of troubleshooting. Sometimes, your remote is not to blame. There is no need to go through the process of buying and programming a remote when it wasn't causing your issue. Here are some common problems you may see that could seem like a remote issue but that are due to something else.

Before you do anything with your remote or any further troubleshooting, The Family Handyman suggests that you make sure you can manually open and close the garage door. If you cannot do this, there might be a more serious issue, such as broken springs or a damaged track, which will require professional service. If you can manually open the door, then you can move onto looking at what may be wrong.

Remote Issues

The easiest thing to check first is your remote. If you have other remotes and they work, then you should replace the batteries in your remote. If that doesn't fix the issue, then follow the steps for how to program a Genie garage door opener to reset your remote. This may be all that you need to do, but if not, continue troubleshooting.

Your next step is to make sure you are within range. You should move closer to the door and see if your remote works. If you find you have to be much closer than you used to, it could be a battery issue. It could also indicate the remote is worn out and you need a new one. Before you buy a new remote and start the steps for how to program a Genie garage door opener, you can move onto more troubleshooting to make sure it isn't a problem with your door.

Door Issues

Custom Door & Gate explains that you want to look for something wrong with the garage door that would affect how the remote operates. If the door opens fine but won't close, it could be the photo eyes are dirty or misaligned. These are part of the safety mechanism that prevents the door from closing on a person or object. To check them, make sure they are clean by lightly wiping them. Check the alignment, measuring from the ground and using a level. Both eyes should line up and face each other.

You also need to check the antenna. When there is damage or a bend in the antenna, it can't receive the signal from your remote properly. That means it may not work all the time or at all. You can visually inspect the antenna. It should hang down from the opener head. If it isn't hanging down, you can adjust it to the right position and try your remote again. Also, check for any obstructions. If you have something in the way of the antenna, it can't pick up signals, so you may just need to move things around in your garage.

If neither of these is the problem, then you can try replacing the remote and following the steps for how to program a Genie garage door opener. Your new remote should work, but if it does not, call a professional. Have them take a look at your garage door system, because there is likely an issue with some other component.

Garage doors with numbers

Image via Pexels

Wrapping Things Up

Learning how to program a Genie garage door opener is something you want to commit to memory. If your remote is not programmed correctly, it just becomes a useless hunk of plastic and electronic components. However, once programmed, it is a very useful tool that will save you a lot of headaches and make your life a bit easier.

Once you program your initial remote, though, you may not think about it again until you need to program a new one. So, make sure you bookmark this article so you can come back anytime you need to refresh your memory on how to program a Genie garage door opener.

Leave a Comment:

Leave a Comment: